web analytics
300-135 braindumps

  • [May 2018] Lead2pass Latest Cisco 300-135 Exam Questions Free Downloading 195q

    Lead2pass 300-135 Dumps PDF Free Download:

    https://www.lead2pass.com/300-135.html

    QUESTION 41
    The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, and FHRP services, a trouble ticket has been operated indicating that Client 1 cannot ping the 209.65.200.241 address.
    Use the supported commands to Isolated the cause of this fault and answer the following questions.
    On which device is the fault condition located?

    A.    R1
    B.    R2
    C.    R3
    D.    R4
    E.    DSW1
    F.    DSW2
    G.    ASW1
    H.    ASW2

    Answer: G
    Explanation:
    Since the Clients are getting an APIPA we know that DHCP is not working. However, upon closer examination of the ASW1 configuration we can see that the problem is not with DHCP, but the fact that the trunks on the port channels are only allowing VLANs 1-9, when the clients belong to VLAN 10. VLAN 10 is not traversing the trunk on ASW1, so the problem is with the trunk configuration on ASW1.

    QUESTION 42
    The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, and FHRP services, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
    Use the supported commands to isolated the cause of this fault and answer the following questions.
    The fault condition is related to which technology?

    A.    NTP
    B.    Switch-to-Switch Connectivity
    C.    Access Vlans
    D.    Port Security
    E.    VLAN ACL / Port ACL
    F.    Switch Virtual Interface

    Answer: B
    Explanation:
    Since the Clients are getting an APIPA we know that DHCP is not working. However, upon closer examination of the ASW1 configuration we can see that the problem is not with DHCP, but the fact that the trunks on the port channels are only allowing VLANs 1-9, when the clients belong to VLAN 10. VLAN 10 is not traversing the trunk on ASW1, so the problem is with switch to switch connectivity, specifically the trunk configuration on ASW1.

    QUESTION 43
    The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, and FHRP services, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
    Use the supported commands to isolated the cause of this fault and answer the following questions.
    What is the solution to the fault condition?

    A.    In Configuration mode, using the interface port-channel 13 command, then configure switchport trunk allowed vlan none followed by switchport trunk allowed vlan 20,200 commands.
    B.    In Configuration mode, using the interface port-channel 13, port-channel 23, then configure switchport trunk none allowed vlan none followed by switchport trunk allowed vlan 10,200 commands.
    C.    In Configuration mode, using the interface port-channel 23 command, then configure switchport trunk allowed vlan none followed by switchport trunk allowed vlan 20,200 commands.
    D.    In Configuration mode, using the interface port-channel 23, port-channel, then configure switchport trunk allowed vlan none followed by switchport trunk allowed vlan 10,20,200 commands.

    Answer: B
    Explanation:
    We need to allow VLANs 10 and 200 on the trunks to restore full connectivity. This can be accomplished by issuing the “switchport trunk allowed vlan 10,200” command on the port channels used as trunks in DSW1.

    Ticket 2 : ACCESS VLAN

    Topology Overview (Actual Troubleshooting lab design is for below network design)

    – Client Should have IP 10.2.1.3
    – EIGRP 100 is running between switch DSW1 & DSW2
    – OSPF (Process ID 1) is running between R1, R2, R3, R4
    – Network of OSPF is redistributed in EIGRP
    – BGP 65001 is configured on R1 with Webserver cloud AS 65002
    – HSRP is running between DSW1 & DSW2 Switches

    The company has created the test bed shown in the layer 2 and layer 3 topology exhibits.
    This network consists of four routers, two layer 3 switches and two layer 2 switches.
    In the IPv4 layer 3 topology, R1, R2, R3, and R4 are running OSPF with an OSPF process number 1.
    DSW1, DSW2 and R4 are running EIGRP with an AS of 10. Redistribution is enabled where necessary.
    R1 is running a BGP AS with a number of 65001. This AS has an eBGP connection to AS 65002 in the ISP’s network. Because the company’s address space is in the private range.
    R1 is also providing NAT translations between the inside (10.1.0.0/16 & 10.2.0.0/16) networks and outside (209.65.0.0/24) network.
    ASW1 and ASW2 are layer 2 switches.
    NTP is enabled on all devices with 209.65.200.226 serving as the master clock source.
    The client workstations receive their IP address and default gateway via R4’s DHCP server.
    The default gateway address of 10.2.1.254 is the IP address of HSRP group 10 which is running on DSW1 and DSW2.
    In the IPv6 layer 3 topology R1, R2, and R3 are running OSPFv3 with an OSPF process number 6.
    DSW1, DSW2 and R4 are running RIPng process name RIP_ZONE.
    The two IPv6 routing domains, OSPF 6 and RIPng are connected via GRE tunnel running over the underlying IPv4 OSPF domain. Redistrution is enabled where necessary.
    Recently the implementation group has been using the test bed to do a `proof-of-concept’ on several implementations. This involved changing the configuration on one or more of the devices. You will be presented with a series of trouble tickets related to issues introduced during these configurations.

    Note: Although trouble tickets have many similar fault indications, each ticket has its own issue and solution.

    Each ticket has 3 sub questions that need to be answered & topology remains same.
    Question-1 Fault is found on which device,
    Question-2 Fault condition is related to,
    Question-3 What exact problem is seen & what needs to be done for solution

    Client is unable to ping IP 209.65.200.241

    Solution:

    Steps need to follow as below:
    – When we check on client 1 & Client 2 desktop we are not receiving DHCP address from R4 Ipconfig — — Client will be getting 169.X.X.X.
    – On ASW1 port Fa1/0/ 1 & Fa1/0/2 access port VLAN 10 was assigned which is using IP address 10.2.1.0/24.
    Sh run ——- & check for running config of int fa1/0/1 & fa1/0/2 ====================================================

    431

    ====================================================

    Here we are not able to see access Vlan10 configured for Port Fa1/0/1 & Fa1/0/2 Change required: On ASW1, for configuring Access Vlan under interface fa1/0/1 & 1/0/2 we have to enable command switchport access vlan 10

    QUESTION 44
    The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
    Use the supported commands to isolated the cause of this fault and answer the following questions.
    What is the solution to the fault condition?

    A.    R1
    B.    R2
    C.    R3
    D.    R4
    E.    DSW1
    F.    DSW2
    G.    ASW1
    H.    ASW2

    Answer: G
    Explanation:
    The problem here is that VLAN 10 is not configured on the proper interfaces on switch ASW1.

    QUESTION 45
    The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
    Use the supported commands to isolated the cause of this fault and answer the following questions.

    The fault condition is related to switch technology?

    A.    NTP
    B.    Switch-to-Switch Connectivity
    C.    Loop Prevention
    D.    Access Vlans
    E.    VLAN ACL Port ACL
    F.    Switch Virtual Interface
    G.    Port Security

    Answer: D
    Explanation:
    The problem here is that VLAN 10 is not configured on the proper interfaces on switch ASW1.

    QUESTION 46
    The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
    Use the supported commands to isolated the cause of this fault and answer the following questions.
    What is the solution to the fault condition?

    A.    In Configuration mode, using the interface range Fastethernet 1/0/1 ?2, then switchport mode access vlan 10 command.
    B.    In Configuration mode, using the interface range Fastethernet 1/0/1 ?2, then switchport access mode vlan 10 command.
    C.    In Configuration mode, using the interface range Fastethernet 1/0/1 ?2, then switchport vlan 10 access command.
    D.    In Configuration mode, using the interface range Fastethernet 1/0/1 ?2, then switchport access vlan 10 command.

    Answer: D
    Explanation:
    The problem here is that VLAN 10 is not configured on the proper interfaces on switch ASW1.

    Ticket 3 : OSPF Authentication

    Topology Overview (Actual Troubleshooting lab design is for below network design)

    – Client Should have IP 10.2.1.3
    – EIGRP 100 is running between switch DSW1 & DSW2
    – OSPF (Process ID 1) is running between R1, R2, R3, R4
    – Network of OSPF is redistributed in EIGRP
    – BGP 65001 is configured on R1 with Webserver cloud AS 65002
    – HSRP is running between DSW1 & DSW2 Switches

    The company has created the test bed shown in the layer 2 and layer 3 topology exhibits.
    This network consists of four routers, two layer 3 switches and two layer 2 switches.
    In the IPv4 layer 3 topology, R1, R2, R3, and R4 are running OSPF with an OSPF process number 1.
    DSW1, DSW2 and R4 are running EIGRP with an AS of 10. Redistribution is enabled where necessary.
    R1 is running a BGP AS with a number of 65001. This AS has an eBGP connection to AS 65002 in the ISP’s network. Because the company’s address space is in the private range.
    R1 is also providing NAT translations between the inside (10.1.0.0/16 & 10.2.0.0/16) networks and outside (209.65.0.0/24) network.
    ASW1 and ASW2 are layer 2 switches.
    NTP is enabled on all devices with 209.65.200.226 serving as the master clock source.
    The client workstations receive their IP address and default gateway via R4’s DHCP server.
    The default gateway address of 10.2.1.254 is the IP address of HSRP group 10 which is running on DSW1 and DSW2.
    In the IPv6 layer 3 topology R1, R2, and R3 are running OSPFv3 with an OSPF process number 6.
    DSW1, DSW2 and R4 are running RIPng process name RIP_ZONE.
    The two IPv6 routing domains, OSPF 6 and RIPng are connected via GRE tunnel running over the underlying IPv4 OSPF domain. Redistrution is enabled where necessary.
    Recently the implementation group has been using the test bed to do a `proof-of-concept’ on several implementations. This involved changing the configuration on one or more of the devices. You will be presented with a series of trouble tickets related to issues introduced during these configurations.

    Note: Although trouble tickets have many similar fault indications, each ticket has its own issue and solution.

    Each ticket has 3 sub questions that need to be answered & topology remains same.
    Question-1 Fault is found on which device,
    Question-2 Fault condition is related to,
    Question-3 What exact problem is seen & what needs to be done for solution

    Client is unable to ping IP 209.65.200.241

    Solution:

    Steps need to follow as below:
    – When we check on client 1 & Client 2 desktop we are not receiving DHCP address from R4 Ipconfig —– Client will be receiving IP address 10.2.1.3
    – IP 10.2.1.3 will be able to ping from R4 , R3, R2 but not from R1

    461

    – Check for neighborship of ospf
    sh ip ospf nei —– Only one neighborship is forming with R2 & i.e. with R3
    Since R2 is connected to R1 & R3 with routing protocol ospf than there should be 2 neighbors seen but only one is seen
    – Need to check running config of R2 & R3 for interface
    Sh run ————————– Interface Serial0/0/0/0.12 on R2

    462

    – Sh run ————————– Interface Serial0/0/0/0 on R1

    – Change required: On R1, for IPV4 authentication of OSPF command is missing and required to configure—— ip ospf authentication message-digest

    QUESTION 47
    The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
    Use the supported commands to isolated the cause of this fault and answer the following questions.
    On which device is the fault condition located?

    A.    R1
    B.    R2
    C.    R3
    D.    R4
    E.    DSW1
    F.    DSW2
    G.    ASW1
    H.    ASW2

    Answer: A
    Explanation:
    As you will see, the problem in this situation is with OSPF on R1. It is missing the “ip ospf authentication message-digest” command on the Serial0/0/0/0.12 interface.

    QUESTION 48
    The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
    Use the supported commands to isolated the cause of this fault and answer the following questions.
    The fault condition is related to which technology?

    A.    BGP
    B.    NTP
    C.    IP NAT
    D.    IPv4 OSPF Routing
    E.    IPv4 OSPF Redistribution
    F.    IPv6 OSPF Routing
    G.    IPv4 layer 3 security

    Answer: D
    Explanation:
    The problem in this situation is with OSPF on router 1. It is missing the “ip ospf authentication messagedigest” command on the Serial0/0/0/0.12 interface.
    The problem statement tells us that the two routers are not able to become OSPF neighbors.

    300-135 dumps full version (PDF&VCE): https://www.lead2pass.com/300-135.html

    Large amount of free 300-135 exam questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDZmFQVlZDZnpLejA

    Maybe you also need:

    300-101 exam dumps:  https://drive.google.com/open?id=0B3Syig5i8gpDakxVRXg3aUpmTE0

    300-115 exam dumps:  https://drive.google.com/open?id=0B3Syig5i8gpDM0pqaFJWUXVuM2M

  • [April 2018] Free Share Lead2pass Cisco 300-135 VCE Dumps With New Update Exam Questions 181q

    Free Share Of Lead2pass 300-135 VCE And PDF Dumps:

    https://www.lead2pass.com/300-135.html

    QUESTION 21
    The following commands are issued on a Cisco Router:

    Router(configuration)#access-list 199 permit tcp host 10.1.1.1 host 172.16.1.1
    Router(configuration)#access-list 199 permit tcp host 172.16.1.1 host 10.1.1.1
    Router(configuration)#exit
    Router#debug ip packet 199

    What will the debug output on the console show?

    A.    All IP packets passing through the router
    B.    Only IP packets with the source address of 10.1.1.1
    C.    All IP packets from 10.1.1.1 to 172.16.1.1
    D.    All IP Packets between 10.1.1.1 and 172.16.1.1 (more…)

  • [January 2018] Free Share Of Lead2pass 300-135 VCE And PDF Dumps 137q

    Free Sharing Of Cisco 300-135 Brain Dumps From Lead2pass:

    https://www.lead2pass.com/300-135.html

    QUESTION 1
    A network administrator is troubleshooting an EIGRP connection between RouterA, IP address 10.1.2.1, and RouterB, IP address 10.1.2.2. Given the debug output on RouterA, which two statements are true? (Choose two.)

    (more…)

  • [2017 New] Lead2pass 100% Valid 300-135 Exam Questions PDF Free Download (76-90)

    2017 August Cisco Official New Released 300-135 Dumps in Lead2pass.com!

    100% Free Download! 100% Pass Guaranteed!

    Thank you so much Lead2pass. You helped me passing my 300-135 exam easily, 90% of the exam questions from the dump appeared in my exam.

    Following questions and answers are all new published by Cisco Official Exam Center: https://www.lead2pass.com/300-135.html

    QUESTION 76
    The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened DSW1 will not become the active router for HSRP group 10.
    Use the supported commands to isolated the cause of this fault and answer the following questions.
    What is the solution to the fault condition?

    A.    Under the interface vlan 10 configuration enter standby 10 preempt command.
    B.    Under the track 1 object configuration delete the threshold metric up 1 down 2 command and enter the threshold metric up 61 down 62 command.
    C.    Under the track 10 object configuration delete the threshold metric up 61 down 62 command and enter the threshold metric up 1 down 2 command.
    D.    Under the interface vlan 10 configuration delete the standby 10 track1 decrement 60 command and enter the standby 10 track 10 decrement 60 command.

    (more…)

  • [2017 New] Lead2pass 100% Valid 300-135 Exam Questions PDF Free Download (61-75)

    2017 August Cisco Official New Released 300-135 Dumps in Lead2pass.com!

    100% Free Download! 100% Pass Guaranteed!

    I was very confused about selecting the best practice test website when preparing for my 300-135 certification exam. Luckly, a friend told me about Lead2pass.com. I passed the 300-135 exam from the first try. Excellent website for free exam dumps!

    Following questions and answers are all new published by Cisco Official Exam Center: https://www.lead2pass.com/300-135.html

    QUESTION 61
    The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
    Use the supported commands to isolated the cause of this fault and answer the following questions.
    What is the solution to the fault condition?

    A.    In Configuration mode, using the interface range Fa 1/0/1 – 2, then no switchport port- security interface configuration commands.
    Then in exec mode clear errdisable interface fa 1/01 – 2 vlan 10 command
    B.    In Configuration mode, using the interface range Fa 1/0/1 – 2, then no switchport port- security, followed by shutdown, no shutdown interface configuration commands.
    C.    In Configuration mode, using the interface range Fa 1/0/1 – 2, then no switchport port- security interface configuration commands.
    D.    In Configuration mode, using the interface range Fa 1/0/1 – 2, then no switchport port- security interface configuration commands.
    Then in exec mode clear errdisable interface fa 1/0/1, then clear errdisable interface fa 1/0/2 commands.

    (more…)

  • [2017 New] Download Free Cisco 300-135 Exam Questions And Answers From Lead2pass (46-60)

    2017 July Cisco Official New Released 300-135 Dumps in Lead2pass.com!

    100% Free Download! 100% Pass Guaranteed!

    Our dumps have been reviewed and approved by industry experts and individuals who have taken and passed 300-135 exam. Lead2pass will have you prepared to take 300-135 test with high confidence and pass easily. Whether you are looking for 300-135 study guide, 300-135 exam questions, 300-135 exam dump or 300-135 test, Lead2pass.com has you covered.

    Following questions and answers are all new published by Cisco Official Exam Center: https://www.lead2pass.com/300-135.html

    QUESTION 46
    The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
    Use the supported commands to isolated the cause of this fault and answer the following questions.
    What is the solution to the fault condition?

    A.    In Configuration mode, using the interface range Fastethernet 1/0/1 ?2, then switchport mode access vlan 10 command.
    B.    In Configuration mode, using the interface range Fastethernet 1/0/1 ?2, then switchport access mode vlan 10 command.
    C.    In Configuration mode, using the interface range Fastethernet 1/0/1 ?2, then switchport vlan 10 access command.
    D.    In Configuration mode, using the interface range Fastethernet 1/0/1 ?2, then switchport access vlan 10 command.

    (more…)

  • [2017 New] Download Free Cisco 300-135 Exam Questions And Answers From Lead2pass (31-45)

    2017 July Cisco Official New Released 300-135 Dumps in Lead2pass.com!

    100% Free Download! 100% Pass Guaranteed!

    Whether you are a student attempting to pass 300-135 exam to be eligible for a post-graduate job, or a working professional hoping to improve your work credentials and earn that dream promotion Lead2pass is here to help. We have 300-135 exam dumps and brain dumps, so passing 300-135 exam is not an easy feat.

    Following questions and answers are all new published by Cisco Official Exam Center: https://www.lead2pass.com/300-135.html

    QUESTION 31
    You have been brought in to troubleshoot an EIGRP network. A network engineer has made configuration changes to the network rendering some locations unreachable. You are to locate the problem and suggest solution to resolve the issue.

     

    R5 has become partially isolated from the remainder of the network. R5 can reach devices on directly connected networks but nothing else. What is causing the problem?

    A.    An outbound distribute list in R3
    B.    Inbound distribute lists in R5
    C.    An outbound distribute list in R6
    D.    Incorrect EIGRP routing process ID in R5

    (more…)

  • [2017 New] Download Free Cisco 300-135 Exam Questions And Answers From Lead2pass (16-30)

    2017 July Cisco Official New Released 300-135 Dumps in Lead2pass.com!

    100% Free Download! 100% Pass Guaranteed!

    Are you worrying about the 300-135 exam? Lead2pass provides the latest 300-135 braindumps and guarantees you passing 300-135 exam beyond any doubt.

    Following questions and answers are all new published by Cisco Official Exam Center: https://www.lead2pass.com/300-135.html

    QUESTION 16
    Which two statements about the Cisco Aironet Desktop Utility (ADU) are true? (Select two)

    A.    The Aironet Desktop Utility (ADU) profile manager feature can create and manage only one profile for the wireless client adapter.
    B.    The Aironet Desktop Utility (ADU) can support only one wireless client adapter installed and used at a time.
    C.    The Aironet Desktop Utility (ADU) can be used to establish the association between the client adapter and the access point, manage authentication to the wireless network, and enable encryption.
    D.    The Aironet Desktop Utility (ADU) and the Microsoft Wireless Configuration Manager can be used at the same time to configure the wireless client adapter.

    (more…)

  • [2017 New] Download Free Cisco 300-135 Exam Questions And Answers From Lead2pass (1-15)

    2017 July Cisco Official New Released 300-135 Dumps in Lead2pass.com!

    100% Free Download! 100% Pass Guaranteed!

    Amazing,100% candidates have passed the 300-135 exam by practising the preparation material of Lead2pass, because the braindumps are the latest and cover every aspect of 300-135 exam. Download the braindumps for an undeniable success in 300-135 exam.

    Following questions and answers are all new published by Cisco Official Exam Center: http://www.lead2pass.com/300-135.html

    QUESTION 1
    A network administrator is troubleshooting an EIGRP connection between RouterA, IP address 10.1.2.1, and RouterB, IP address 10.1.2.2. Given the debug output on RouterA, which two statements are true? (Choose two.)

    A.    RouterA received a hello packet with mismatched autonomous system numbers.
    B.    RouterA received a hello packet with mismatched hello timers.
    C.    RouterA received a hello packet with mismatched authentication parameters.
    D.    RouterA received a hello packet with mismatched metric-calculation mechanisms.
    E.    RouterA will form an adjacency with RouterB.
    F.    RouterA will not form an adjacency with RouterB.

    (more…)